Product ID:AMBERLITE IRA910 CI RESIN, 63232
MSDS Date:07/08/1998
FSC:6850
NIIN:00N091740
Status Code:A
MSDS Number: CJNPZ

Emergency Phone: 215-592-3000

Info Phone: 215-592-2521

Cage: 77902

Telephone: 215-592-2521/215-592-3000

Cage: 77902

QUAT AMINE DIVINYLBENZENE/STYRENE COPOLYMER, CI ION FORM

CAS: 63181-94-2

OSHA PEL N/K

ACGIH TLV: N/K

WATER

CAS: 7732-18-5

RTECS: ZC0110000

OSHA PEL N/K

ACGIH TLV: N/K

LD50 LC50 Mixture:SEE TOXICOLOGICAL INFORMATION.
Routes of Entry: Inhalation:NO Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYES: MATERIAL CAN CAUSE SLIGHT
IRRITATION. SKIN: PROLONGED OR REPEATED SKIN CONTACT CAN CAUSE
SLIGHT IRRITATION.
Effects of Overexposure:SEE HEALTH HAZARDS.

First Aid:EYES: FLUSH EYES WITH A LARGE AMOUNT OF WATER FOR AT LEAST 15
MINUTES. CONSULT A PHYSICIAN IF IRRITATION PERSISTS. SKIN: WASH
SKIN THOROUGHLY WITH SOAP AND WATER. INHALATION: REMOVE TO FRESH
AIR. SUPP ORT BREATHING (GIVE OXYGEN OR ARTIFICIAL RESPIRATION) .
INGESTION: CALL MD IMMEDIATELY .

Autoignition Temp:=500.C, 932.F
Autoignition Temp Text:ESTIM
Extinguishing Media:CARBON DIOXIDE, DRY CHEMICAL, WATER SPRAY.
Fire Fighting Procedures:WEAR NIOSH APPROVED SCBA AND FULL PROTECTIVE
EQUIPMENT .
Unusual Fire/Explosion Hazard:COMBUSTION GENERATES TOXIC FUMES OF
NITROGEN OXIDES, AND HYDROGEN CHLORIDE.

Spill Release Procedures:WEAR GLOVES MADE OF COTTON, CANVAS OR LEATHER.
ADDITIONAL PERSONAL PROTECTIVE EQUIPMENT SHOULD INCLUDE SAFETY
GLASSES (ANSI Z87.1 OR APPROVED EQUIVALENT). FLOOR MAY BE SLIPPERY;
USE CARE TO AVOID FALL ING. TRANSFER SPILLED MATERIAL TO SUITABLE
CONTAINERS FOR RECOVERY OR DISPOSAL.

Handling and Storage Precautions:AVOID RPTD FREEZE-THAW CYCLES; BEADS
MAY FRACTURE. IF FROZEN, THAW AT ROOM TEMP. NOTE: THIS PROD AS
SUPPLIED IS A WHOLE BEAD ION EXCHANGE RESIN & MAY PRDCE SLIGHT EYE
IRRIT. HOWEVER, GROUND FORM OF TH IS ION EXCHANGE RESIN SHOULD BE
TREATED AS SEVERE EYE IRRITANT.
Other Precautions:WORKER EXPOS TO GROUND RESINS CAN BE CONTROLLED W/LOC
EXHST VENT AT POINT OF DUST GENERATION/USE OF SUITABLE PERS PROT
EQUIP (DUST/MIST AIR-PURIFYING RESP & SFTY GOGGS). PROPERLY
DESIGNED EQUIP IS VIT AL IF THESE RESINS ARE TO BE USED IN
CONJUNCTION W/STRONG OXIDIZING AGENTS SUCH AS NITRIC ACID TO PV NT
RAPID (SUP DAT)

Respiratory Protection:A RESPIRATORY PROTECTION PROGRAM MEETING OSHA
1910.134 AND ANSI Z88.2 REQUIREMENTS MUST BE FOLLOWED WHENEVER
WORKPLACE CONDITIONS WARRANT A RESPIRATOR'S USE. NONE REQUIRED
UNDER NORMAL OPERATING CONDI TIONS. WEAR NIOSH APPROVED RESPIRATOR
APPROPRIATE FOR EXPOSURE OF CONCERN .
Ventilation:VENT SYS EMPLOYED IS DEPENDENT ON USER'S SPECIFIC
APPLICATION OF THIS MATL. REFER TO CURRENT EDITION OF INDUS VENT: A
MANUAL OF REC PRACT PUBLISHED (OTHER INFO)
Protective Gloves:COTTON, CANVAS, OR LEATHER GLOVES.
Eye Protection:ANSI APPROVED CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:ANSI APPROVED EMERGENCY EYEWASH AND DELUGE
SHOWER . WHEN USING THIS SUBSTANCE, USE SKIN PROTECTION.
Work Hygienic Practices:AVOID SKIN CONTACT. GLOVES SHOULD BE REMOVED
AND REPLACED IMMEDIATELY IF THERE IS ANY INDICATION OF DEGRADATION
OR CHEMICAL BREAKTHROUGH.
Supplemental Safety and Health
OTHER PREC: BUILD-UP OF PRESS & POSS EXPLO. CONSULT SOURCE
KNOWLEDGEABLE IN HNDLG OF THESE MATLS BEFORE PROCEEDING. DO NOT
PACK COLUMN W/DRY ION EXCHANGE RESINS. DRY BEADS EXPAND WHEN
WETTED; THIS EXP ANSION CAN CAUSE GLASS COLUMNS TO SHATTER. PH: 5-9
AQUEOUS SLURRY.

Boiling Pt:=100.C, 212.F
B.P. Text:WATER
Melt/Freeze Pt:=0.C, 32.F
M.P/F.P Text:WATER
Vapor Pres:17 MM HG @ 20C/68F(WATER)
Vapor Density:<1 (AIR=1)
Spec Gravity:1.05-1.15 (WATER=1)
pH:SUP DAT
Evaporation Rate & Reference:<1 (BUTYL ACETATE=1)
Solubility in Water:PRACTICALLY INSOLUBLE
Appearance and Odor:AMBER BEADS.
Percent Volatiles by Volume:<10% (WATER)

Stability Indicator/Materials to Avoid:YES
AVOID CONTACT WITH STRONG OXIDIZING AGENTS, PARTICULARLY CONCENTRATED
NITRIC ACID.
Stability Condition to Avoid:THIS MATERIAL IS CONSIDERED STABLE UNDER
SPECIFIED CONDITIONS OF STORAGE, SHIPMENT AND/OR USE. HOWEVER,
AVOID TEMPERATURES ABOVE 190C.
Hazardous Decomposition Products:THERMAL DECOMPOSITION MAY YIELD
MONOMER VAPORS, ALKYLAMINES, OXIDES OF NITROGEN, AND HYDROGEN
CHLORIDE.

Waste Disposal Methods:UNUSED RESIN MAY BE INCINERATED OR LANDFILLED IN
FACILITIES MEETING LOCAL, STATE, AND FEDERAL REGULATIONS. FOR
CONTAMINATED RESIN, THE USER MUST DETERMINE THE HAZARD AND USE AN
APPROVED DISPOSAL METHO D.

Toxicological Information:TOXICITY DATA FOR A COMPOSITIONALLY SIMILAR
MATERIAL ARE LISTED BELOW. ORAL LD50 - RAT: >5000 MG/KG. DERMAL
LD50 - RABBIT: >5000 MG/KG. MUTAGENICITY DATA: AMES MUTAGENICITY:
NON=MUTAGENIC.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.

Ecological:NO APPLICABLE DATA.

Transport Information:US DOT HAZARD CLASS: NONREGULATED.

SARA Title III Information:SECTION 311/312 CATEGORIZATIONS (40 CFR
370): THIS PRODUCT IS NOT A HAZARDOUS CHEMICAL UNDER 29 CFR
1910.1200, AND THEREFORE IS NOT COVERED BY TITLE III OF SARA.
SECTION 313 INFORMATION (40 CFR 372): THIS PRODUCT DOES NOT
CONTAIN A CHEMICAL WHICH IS LISTED IN SECTION 313 AT OR ABOVE DE
MINIMIS CONCENTRATIONS.
Federal Regulatory Information:WORKPLACE CLASSIFICATION: THIS PROD IS
CONSIDERED NON-HAZ UNDER OSHA COMMUNICATION STD (29 CFR 1910.1200).
THIS PROD IS NOT A 'CONTROLLED PROD' UNDER CANADIAN WORKPLACE HAZ
MATLS INFO SYS (WHMIS). CER CLA INFO (40 CFR 302.4): RELEASES OF
THIS MATL TO AIR, LAND/WATER ARE NOT REPORTABLE TO NATL RESPONSE
CTR UNDER COMPREHENSIVE ENVIRON RESPONSE, COMPENSATION, & LIABILITY
ACT (CERCLA)/TO STATE & LOCAL EMER PLANNING COMMITTEES UNDER SARA
TITLE III SECTION 304. WASTE CLASSIFICATION: WHEN A DECISION IF
MADE TO DISCARD THIS MATL AS SUPPLIED, IT DOES NOT MEET RCRA'S
CHARACT DEFINITION OF IGNITABILITY, CORROSIVITY/REACTIVITY, (STATE
REGS)
State Regulatory Information:FEDERAL REGULATIONS: AND IS NOT LISTED IN
40 CFR 261.33. THE TOXICITY CHARACTERISTIC (TC), HOWEVER, HAS NOT
BEEN EVALUATED BY THE TOXICITY CHARACTERISTIC LEACHING PROCEDURE
(TCLP). UNITED STATES: ALL COMPONENTS OF THIS PRODUCT ARE PRODUCED
IN COMPLIANCE WITH THE REQUIREMENTS OF THE U.S. TOXIC SUBSTANCES
CONTROL ACT (TSCA) AND ARE EITHER LISTED ON OR ARE EXEMPT FROM
LISTING ON THE INVENTORY. FOR CE RTAIN POLYMERIC SUBSTANCES, THE
POLYMER EXEMPTION CITED AT 40 CFR 723.250 MAY APPLY.